ES010 Epoxy Sealer
General Description

"SEAL-IT" Epoxy Concrete Sealer, 21ES10, is a two component solvent based epoxy coating designed as a thin film sealer for application to properly prepared concrete and steel surfaces prior to application of a complete coating system. The applied coating displays excellent resistance to abrasion, fresh and salt water, detergents, and most chemicals as well as good resistance to acids, alkalis, fume and spillage of most organic solvents. It provides extended service life in Industrial, Marine and commercial applications. In UV exposed areas a topcoat is recommended.

ES010 is designed for industrial, and commercial use as a protective maintenance coating for industrial plants, pulp and paper mills, textile mills, chemical processing plants, waste water plants, refineries, food processing plants, commercial buildings and marine structures. For coating and protection of storage tanks, piping, roof decks, water towers, structural steel machinery, plant equipment, marine vessels, offshore structures and other surfaces exposed to humidity, chemicals and corrosive environment.

IconSpecification

Vehicle Type Solvent based Epoxy
Solids Content ± 2% 46% by weight, mixed
35.0% by volume, mixed
Coverage (Theoretical) 280 sqft per gallon at 2 mil DFT
6.87 sq m/liter @50micron DFT, unthinned (0% loss factor)
Coverage (Estimated) 225 sqft /gallon at 2.0 mil DFT
5.50 sq m/liter at 50 microns (20% loss factor)
Number of Coats Normally one coat @ min 2.0 - 3.0 mils DFT, 2 coats if required (concrete porosity is an important factor in coverage and thickness)
Application Method Airless Spray preferred - Conventional spray acceptable, brush for small areas if necessary
Thinner Mopoxy Spraying Thinner75-37, Brushing Thinner 75-35
Clean up solvent No. 7535, No. 7537, MEK or MIBK
Shelf Life at 75° F One Year from Date of Manufacture, unmixed, stored at 40 - 100°F (Re-inspect after 12 months)
Curing
(Drying time at 75 ° F)
2 hours to touch
8 hours to handle (You can apply an FPU top coat when ES010 is dry to handle)
24 days to re coat
Induction Time 15-30 minutes @ 75� F (See "Mixing" below)
Flash Point (Seta Flash) 74°F (23°C) for Component A
53°F (12°C) for Component B
Color, Gloss Clear (Gloss and Semi-gloss)
Pot Life 12-16 hours at 70°F (21°C),
6-8 hours at 90°F 32°C
Mixing Ratio 1 to 1 by volume
VOC Content 4.3 lbs/gal; (515 grams/liter), calculated
Shipping Information 11 lbs per gallon including container (4.99 Kg)
Freight PAINT, FLAMMABLE LIQUID, UN1263

IconSurface Preparation

Good surface preparation is essential to a satisfactory coating system. Surfaces to be coated should be clean and dry. Remove all oil, grease, mildew or other contamination by solvent or detergent cleaning or other effective means.

Limitations:

Apply in good weather when air and surface temperature are above 50�F and surface temperature is at least 5° F above the dew point. For optimum application properties, material should be between 70° to 100°F prior to mixing and application. Maintain unmixed material in closed containers in protected storage at 40° to 100° F.

Previously Finished Surfaces:

Repair all damaged areas. Remove gloss from previous paint by sanding or "brush blasting" (SSPC-SP7). Remove rust, corrosion products, heavy chalk and loose or peeling paint by "hand or power tool cleaning" (SSPC-SP2) Spot prime with SEAL - IT any bare areas as in new work. If doubt exists concerning compatibility of this coating with the previous system, apply coating to a representative area (55 square feet minimum) and allow to cure and age several weeks. Then inspect for adhesion failure, wrinkling, lifting, blistering or any sign of incompatibility. If there are no signs, coating work can proceed.

Concrete:

Surface must be clean, dry, properly cured and free from all contaminants and laitance. Remove all dust before coating. Apply by brush one coat of "SEAL-IT" Clear epoxy sealer 21ES10 over any crevices, bug holes or spalleds. Apply "SEAL-IT" 21ES10 over entire area to a minimum of 2.0 mils DFT (50 microns ), approximately 5-6 mils wet. Allow to dry at least 12 hours. Application on very porous surfaces may require multiple coats to assure that the surface is completely sealed. Apply a full coat of succeeding coat intermediate and FPUWC series Topcoat, over entire area.

IconMixing

This is a two component coating supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Use a power agitator for each component. Allow a 15 - 30 minutes induction time @ 70�F and remix before application before using the coating. Usable pot life depends on the temperature of the material (see the Specification Section, above). Agitate before use, with occasional stirring during use. As pot life expires, sag resistance may be reduced. Do not mix any more materials than can be applied in approximately 1 � hours @ 75�F.

Thinning

Material is supplied at airless spray viscosity and should not require thinning. If required thin with 10% No. 75-37 thinner per gallon if necessary for spray application, No. 7535 for brush application. Add thinner only at a time of mixing. Do not add thinner to thickening material to extend pot life.

Icon Application

Spray application is preferred for proper film build and best performance. Brush application is acceptable for touch up. Roller application may require special care to prevent bubbling and may require more than one coat to attain proper film thickness. Apply at 5.2 mils wet film thickness to achieve 3.0 mils dry film thickness, unthinned.

IconPrecautions

Safe storage, handling and use dictate that adequate health and safety precautions e observed with this product and any recommended thinners. User is specifically directed to consult the current Material Safety Data Sheet for this product as well as precautions contained on product labeling.

Notice- The technical data contained herein are true and accurate to the best of our knowledge. All products are offered and subject to the manufacturer standard conditions of sale. Published technical data and instructions are subject to change without prior notice.

Logo

Additional Information


For additional information contact your Distributor or :
21st Century Coatings, Inc.
4701 Willard Ave., #426
Chevy Chase, MD 20815
Tel: (301) 654-0099 Cell: (301) 873-5230
Email: johnshammas@gmail.com